When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
TESTING & COSMETIC NOTES:
This is a USED WORKING item in GOOD cosmetic condition that IS THOROUGHLY TESTED and is GUARANTEED WORKING
The unit has been reset to the factory default settings. See console log below. Power cords not included.
COMPONENTS INCLUDED IN THIS sale:• (1) - CISCO WS-C3850-48U-S V06 48-PORT UPOE GIGABIT SWITCH
• (1) - CISCO C3850-NM-2-10G MODULE
• (2) - CISCO PWR-C1-1100WAC POWER SUPPLY
REPLACEMENT or MONEY BACK GUARANTEE:When you receive a Guaranteed item from OC Depot, it should perform as described. In the rare situation that this is not the case, we will send a replacement upon safe return of the original item within 30 days of receiving the item. If a replacement is not available we will honor the terms of our Money-Back Guarantee.
ADDITIONAL INFORMATION:Booting...
Interface GE 0 link down***ERROR: PHY link is down
The "IP_ADDR" environment variable is not set.
Getting rest of image
Reading full image into memory...Check base package header ...: done = 16384
Getting rest of image
Reading full image into memory....done
Reading full base package into memory...: done = 32798679
Bundle Image
Kernel Address : 0x537783c0
Kernel Size : 0x438356/4424534
Initramfs Address : 0x53bb0716
Initramfs Size : 0x1ab68c1/28010689
Compression Format: mzip
Bootable image at @ ram:0x537783c0
Bootable image segment 0 address range [0x81100000, 0x81da5280] is in range [0x8
0180000, 0x90000000].
@@@@@@@@@@@@@@@@@@@@@@boot_system: 623
Loading Linux kernel with entry point 0x81895bf0 ...
Bootloader: Done loading app on core_mask: 0xf
### Launching Linux Kernel (flags = 0x5)
Linux version 4.9.187 (xelinux@sjc-xelinux3) (gcc version 5.3.0 (GCC) ) #1 SMP W
ed Nov 4 12:00:14 PST 2020
CVMSEG size: 2 cache lines (256 bytes)
Cavium Inc. SDK-5.1.0
bootconsole [early0] enabled
CPU0 revision is: 000d900a (Cavium Octeon II)
Checking for the multiply/shift bug... no.
Checking for the daddiu bug... no.
Final tar file: mcu_ucode_bundle_6_2_0.tar
Both links down, not waiting for other switches
Switch number is 1
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSAL
K9-M), Version 16.12.5b, RELEASE SOFTWARE (fc3)
Technical Support: http:/www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Thu 25-Mar-21 13:09 by mcpre
This software version supports only Smart Licensing as the software licensing me
chanism.
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO SOFTWARE PRODUCT, PRODUCT FEATURE,
AND/OR SUBSEQUENTLY PROVIDED SOFTWARE FEATURES (COLLECTIVELY, THE
"SOFTWARE"), AND/OR USING SUCH SOFTWARE CONSTITUTES YOUR FULL
ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU
ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN.
Your use of the Software is subject to the Cisco End User License Agreement
(EULA) and any relevant supplemental terms (SEULA) found at
You hereby acknowledge and agree that certain Software and/or features are
licensed for a particular term, that the license to such Software and/or
features is valid only for the applicable term and that such Software and/or
features may be shut down or otherwise terminated by Cisco after expiration
of the applicable license term (e.g., 90-day trial period). Cisco reserves
the right to terminate any such Software feature electronically or by any
other means available. While Cisco may provide alerts, it is your sole
responsibility to monitor your usage of any such term Software feature to
ensure that your systems and networks are prepared for a shutdown of the
Software feature.
FIPS: Flash Key Check : Begin
FIPS: Flash Key Check : End, Not Found, FIPS Mode Not Enabled
All TCP AO KDF Tests Pass
cisco WS-C3850-48U (MIPS) processor (revision AB0) with 794888K/6147K bytes of m
emory.
Processor board ID FOC2134L0ZA
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
1609272K bytes of Flash at flash:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : 70:1f:53:55:ea:80
Motherboard Assembly Number : 73-15799-08
Motherboard Serial Number : FOC213243MF
Model Revision Number : AB0
Motherboard Revision Number : A0
Model Number : WS-C3850-48U
System Serial Number : FOC2134L0ZA
Press RETURN to get started!
*Sep 20 22:15:43.440: %SMART_LIC-6-EXPORT_CONTROLLED: Usage of export controlled
features is not allowed
*Sep 20 22:15:46.785: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is ini
tialized
*Sep 20 22:15:46.786: %SMART_LIC-6-AGENT_ENABLED: Smart Agent for Licensing is e
nabled
*Sep 20 22:15:46.793: %SMART_LIC-6-EXPORT_CONTROLLED: Usage of export controlled
features is not allowed
*Sep 20 22:15:49.681: %SMART_LIC-6-HA_ROLE_CHANGED: Smart Agent HA role changed
to Active.RA Tracing tool registry return: 0
*Sep 20 22:15:59.652: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for typ
e vlan
*Sep 20 22:16:01.345: %LINK-3-UPDOWN: Interface Lsmpi18/3, changed state to up
*Sep 20 22:16:01.347: %LINK-3-UPDOWN: Interface EOBC18/1, changed state to up
*Sep 20 22:16:01.348: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed stat
e to down
*Sep 20 22:16:01.348: %LINK-3-UPDOWN: Interface LIIN18/2, changed state to up
*Sep 20 22:16:01.807: %HMANRP-6-HMAN_IOS_CHANNEL_INFO: HMAN-IOS channel event fo
r switch 1: EMP_RELAY: Channel UP!
*Sep 20 22:16:01.827: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP
switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with
mgmt port UP
*Sep 20 22:15:20.709: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: S
tack port 1 on Switch 1 is nocable
*Sep 20 22:15:20.709: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: S
tack port 2 on Switch 1 is down
*Sep 20 22:15:20.709: %STACKMGR-6-STACK_LINK_CHANGE: Switch 1 R0/0: stack_mgr: S
tack port 2 on Switch 1 is nocable
*Sep 20 22:15:20.710: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch
1 has been added to the stack.
*Sep 20 22:15:24.968: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch
1 has been added to the stack.
*Sep 20 22:15:26.975: %STACKMGR-4-SWITCH_ADDED: Switch 1 R0/0: stack_mgr: Switch
1 has been added to the stack.
*Sep 20 22:15:26.975: %STACKMGR-6-ACTIVE_ELECTED: Switch 1 R0/0: stack_mgr: Swit
ch 1 has been elected ACTIVE.
*Sep 20 22:16:01.838: %HMANRP-6-EMP_NO_ELECTION_INFO: Could not elect active EMP
switch, setting emp active switch to 0: EMP_RELAY: Could not elect switch with
mgmt port UP
*Sep 20 22:16:02.452: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi18/3,
changed state to up
*Sep 20 22:16:02.453: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC18/1,
changed state to up
*Sep 20 22:16:02.454: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0/0, changed state to up
*Sep 20 22:16:02.454: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN18/2,
changed state to up
*Sep 20 22:16:04.542: %SYS-5-CONFIG_P: Configured programmatically by process MG
MT VRF Process from console as vty0
*Sep 20 22:16:04.553: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-
vrf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Sep 20 22:16:04.556: %SYS-5-CONFIG_P: Configured programmatically by process MG
MT VRF Process from console as vty0
*Sep 20 22:16:04.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
nged state to down
*Sep 20 22:16:07.141: %SYS-7-NVRAM_INIT_WAIT_TIME: Waited 0 seconds for NVRAM to
be available
*Sep 20 22:16:07.495: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-
3254604020 has been generated or imported by crypto config
*Sep 20 22:16:07.579: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: TP-self-signed-32546
04020 created succesfully
*Sep 20 22:16:07.601: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: SLA-TrustPoint creat
ed succesfully
*Sep 20 22:16:07.747: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Base was enable
d by Default
*Sep 20 22:16:08.158: %SYS-5-CONFIG_I: Configured from memory by console
*Sep 20 22:16:08.403: %SYS-5-CONFIG_P: Configured programmatically by process CP
P MQC QoS Policy manager from console as vty1
*Sep 20 22:16:08.506: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed stat
e to up
*Sep 20 22:16:09.193: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 20 22:16:09.193: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 20 22:16:09.193: %EVENT_TRACE-6-ENABLE
Switch>
Switch>
Switch>
Switch>: Trace already enabled.
*Sep 20 22:16:09.194: %EVENT_TRACE-6-ENABLE: Trace already enabled.
*Sep 20 22:16:09.865: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Sep 20 22:16:10.056: %SYS-5-RESTART: System restarted --
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSAL
K9-M), Version 16.12.5b, RELEASE SOFTWARE (fc3)
Technical Support: http:/www.cisco.com/techsupport
Copyright (c) 1986-2021 by Cisco Systems, Inc.
Compiled Thu 25-Mar-21 13:09 by mcpre
*Sep 20 22:16:11.004: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/1, changed st
ate to down
*Sep 20 22:16:11.006: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/2, changed st
ate to down
*Sep 20 22:16:11.006: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/3, changed st
ate to down
*Sep 20 22:16:11.006: %LINK-3-UPDOWN: Interface GigabitEthernet1/1/4, changed st
ate to down
*Sep 20 22:16:11.007: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/1, changed
state to down
*Sep 20 22:16:11.007: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/2, changed
state to down
*Sep 20 22:16:11.008: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/3, changed
state to down
*Sep 20 22:16:11.008: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/1/4, changed
state to down
*Sep 20 22:16:11.738: %LINK-3-UPDOWN: Interface Vlan1, changed state to up
*Sep 20 22:16:12.007: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet1/1/1, changed state to down
*Sep 20 22:16:12.008: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet1/1/2, changed state to down
*Sep 20 22:16:12.008: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet1/1/3, changed state to down
*Sep 20 22:16:12.008: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet1/1/4, changed state to down
*Sep 20 22:16:12.009: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabit
Ethernet1/1/1, changed state to down
*Sep 20 22:16:12.009: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabit
Ethernet1/1/2, changed state to down
*Sep 20 22:16:12.010: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabit
Ethernet1/1/3, changed state to down
*Sep 20 22:16:12.010: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabit
Ethernet1/1/4, changed state to down
*Sep 20 22:16:12.462: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-
3254604020.server has been generated or imported by crypto-engine
*Sep 20 22:16:13.360: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed stat
e to down
*Sep 20 22:16:14.361: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0/0, changed state to down
*Sep 20 22:16:14.810: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Start
up Config Present)
*Sep 20 22:16:18.475: %SYS-5-CONFIG_P: Configured programmatically by process EP
M CREATE DEFAULT CWA URL ACL from console as console
*Sep 20 22:16:19.846: %PKI-2-NON_AUTHORITATIVE_CLOCK: PKI functions can not be i
nitialized until an authoritative time source, like NTP, can be obtained.
*Sep 20 22:16:22.780: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI_LE
GACY created succesfully
*Sep 20 22:16:22.823: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_SU
DI_LEGACY has been generated or imported by pki-sudi
*Sep 20 22:16:22.921: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI_LE
GACY0 created succesfully
*Sep 20 22:16:22.936: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI cr
eated succesfully
*Sep 20 22:16:22.972: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_SU
DI has been generated or imported by pki-sudi
*Sep 20 22:16:23.186: %PKI-6-TRUSTPOINT_CREATE: Trustpoint: CISCO_IDEVID_SUDI0 c
reated succesfully
*Sep 20 22:16:23.197: %IOSXE_INFRA-6-PROCPATH_CLIENT_HOG: IOS shim client 'pkiss
l reader mqipc' has taken 261 msec (runtime: 251 msec) to process a 'unknown' me
ssage
Switch>
*Sep 20 22:16:33.349: %PLATFORM_PM-6-FRULINK_INSERTED: 2x1G 2x10G uplink module
inserted in the switch 1 slot 1
Switch>
*Sep 20 22:16:41.064: %SMART_LIC-6-EXPORT_CONTROLLED: Usage of export controlled
features is not allowed Please Click Here to Visit Our StoreSearchBy17 - 263715 | Loc: F13 | L: Mitchell |T: | PM: Nick | QTY: 0| Plan: 50/50 NET of FEES FREESHIP |22.00"x22.00"x5.00"27.00lbs |Start: $0.00 | BIN: $109.99 | |2024-09-23 ||51268
